Menu
Cart 0
IPS Weld-On #42 Acrylic Adhesive Glue 50ml Cartridge - Plastic-Craft Products

Must Be Shipped Ground

IPS Weld-On #42 Acrylic Adhesive Glue Cartridge

  • $39.99

Size
Add Mixing Tip & Applicator

  • SCIGRIP 42 is recommended for bonding of acrylic plastics especially where good clarity retention is required
  • It is versatile having many applications in the sign industry and in the manufacturing and repair of aquariums, museum quality cases and other plastics fabrication industries
  • This product meets Military Spec A-8576C Type III
Description
IPS's Weld-On #42 50ml Cartridge is meant for use with Weld-On's manual applicator gun. It is a two-component 10:1 reactive, high strength acrylic based adhesive that provides "museum quality" water clear joints. It has excellent weatherability. Mil Spec A-8576C
Technical
Technical Data Sheet

TYPICAL BOND STRENGTH

Temperature Aged Bond Strength, lbs/in2 (kg/cm2)
24 Hours 1 Week
Room temperature 2600 (182.8) 4000 (281.0)
120°F (49°C) 4500 (316.0) 5700 (401.8)
150°F (66°C) 5900 (414.8) 7000 (492.0)

Substrate thickness: 0.25 inch (0.64 cm). Bond area: 1.0 in2 (6.45 cm2)

ADHESIVE PROPERTIES AND CHARACTERISTICS

Color Clear Fixture Time 2 Hours
Viscosity 2900 cps Time to reach 80% of ultimate bond strength 72 Hours
Reactivity 20 Minutes Specific Gravity 1.03 ± 0.04
Working Time 15 Minutes Shelf Life 1 year
Directions

DIRECTIONS FOR USE

  • Always wear safety glasses and disposable polyethylene gloves.
  • Load cartridge into adhesive dispenser and remove nose plugs from the cartridge by unscrewing the retaining nut.
  • Dispense a small amount of the resin and catalyst from the cartridge by depressing the trigger. Make sure both materials flow freely from the cartridge, checking for any blockages. Place the mixer tip on the cartridge and secure the remaining nut. Discard the first 6-12 inches of the material and proceed.
  • IF THE MATERIAL IS NOT COMPLETELY USED WITH ONE APPLICATION, IT CAN BE PRESERVED. Leave the mixer tip in place and its presence will temporarily reseal the cartridge. To restore the cartridge to its original state, remove the used mixer tip, clean the threaded areas thoroughly ensuring there is NO crossover of the two components. Remove any blockages that may have formed in the nose area. DO NOT FORCE BLOCKAGES BACK INTO THE CARTRIDGES.
  • Always use a new mixer tip. Never attempt to force material through a blocked opening or a used mixer tip. Discard the first 6-12 inches of material whenever a new tip is used.
Safety
Safety Data Sheet

SAFETY AND ENVIRONMENTAL PRECAUTIONS

This product is a flammable, reactive adhesive. It is considered a hazardous material. In conformance with the Federal Hazardous Substance Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state, and federal labeling, safety and other regulations. VOC emissions do not exceed 75 grams per liter.

WARNING! FLAMMABLE. VAPOR HARMFUL. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE SKIN OR EYES.

Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store away from direct sunlight in a cool 50º – 80ºF (10º – 27º C) dry place. Use only in well ventilated area. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values contained in Section II and VIII of Material Safety Data Sheet If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short term exposure. For emergency and other conditions where shortterm exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, goggles and impervious apron should be used. Carefully read Material Safety Data Sheet and follow all precautions. Contains Methyl Methacrylate Monomer (80-62-6). Do not use this product for other than intended use. “Title III Section 313 Supplier Notification:” This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all Material Safety Data Sheets that are copied and distributed for this material.

FIRST AID

Inhalation: If overcome with vapors, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.

Eye Contact: Flush with plenty of water for 15 minutes and call a physician.

Skin Contact: Wash skin with plenty of soap and water for at least 15 minutes. If irritation develops, get medical attention.

Ingestion: If swallowed, give 1 or 2 glasses of water or milk. Do not induce vomiting. Contact physician or poison control center immediately

SHIPPING

Shipping Information for One Liter Kit and Above: Proper Shipping Name: Adhesive. Hazard Class: 3. Identification Number: UN 1133. Packing Group: II. Label Required: Flammable Liquid.

For Less than One Liter: Proper Shipping Name: Consumer Commodity. Hazard Class: ORM-D.


We Also Recommend