Menu
Cart 0
SCIGRIP IPS Weld-On #1829 Adhesive - for Plastics, Vinyl, Acrylic, Wood, Metal, and More!

Must Be Shipped Ground

SCIGRIP IPS Weld-On #1829 Adhesive - for Plastics, Vinyl, Acrylic, Wood, Metal, and More!

  • $11.42

Size

  • Used in upholstering vinyl seats, bonding vinyl to urethane foam,& canvas
  • Bonding aluminum or vinyl extrusions to concrete, repair of sporting equipment, leather goods, shoes, saddles, belts and handbags
  • SCIGRIP 1829 is being used in marine applications for bonding plasticized vinyls to masonry and metal and patching vinyl sheets
Description
IPS's Weld-On #1829 is intended for many plastics and non-plastic materials. Some examples are vinyl, acrylics, urethane, foam, polyester, wood, metal, etc. It takes 24 hours before 80% of the ultimate bond strength is reached. Available in 4 oz.
Technical
Download - Technical Data Sheet
Color Tan Fixture Time 2 - 4 Hours
Viscosity 1750 ± 250 cps Time to reach 80% of ultimate bond strength 16 – 24 Hours
Specific Gravity 0.862 ± 0.01 Coverage 10 mil: 26 sq ft/pint 210 sq ft/gallon
20 mil: 13 sq ft/pint 105 sq ft/gallon
Working Time 2 – 5 Minutes Shelf Life 2 years expectancy in tightly sealed containers
Directions

DIRECTIONS FOR USE

Clean surfaces to be joined. Coat each mating surface (2 coats if porous). Allow about 2 to 5 minutes for each to dry before assembly. Film should be slightly tacky but not enough to transfer to the fingers using a light touch. Heavy coating may require slightly longer to dry. Press parts firmly together. Use clamps or weights until cement has set sufficiently for handling strength. If parts are strained, do not remove clamps for at least a few hours, depending on materials and room temperature. Initial bond is suitable for handling. For good strength, allow 16 to 24 hours and bond strength will continue to increase for a number of weeks. When applying cement to one piece, bring other piece in contact immediately and maintain contact for a few hours before removing clamps or weights.

Safety
Download - Safety Data Sheet

SAFETY AND ENVIRONMENTAL PRECAUTIONS

This product is a flammable, fast evaporating solvent cement. It is considered a hazardous material. In conformance with the Federal Hazardous Substance Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state, and federal labeling, safety and other regulations.

WARNING! FLAMMABLE. VAPOR HARMFUL. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE SKIN OR EYES.

Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store away from direct sunlight between 40º – 110ºF (5º – 43ºC). Use only with adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency and other conditions where shortterm exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, safety goggles and impervious apron should be used. Carefully read Material Safety Data Sheet and follow all precautions. Contains Methyl Ethyl Ketone (78-93-3). Do not use this product for other than intended use. “Title III Section 313 Supplier Notification”: This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all Material Safety Data Sheets that are copied and distributed for this material.

FIRST AID

Inhalation: If overcome with vapors, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.

Eye Contact: Flush with plenty of water for 15 minutes and call a physician.

Skin Contact: Wash skin with plenty of soap and water for at least 15 minutes. If irritation develops, get medical attention.

Ingestion: If swallowed, give 1 or 2 glasses of water or milk. Do not induce vomiting. Contact physician or poison control center immediately.

SHIPPING

Shipping Information for Gallon and Above: DOT Shipping Name: Adhesive. DOT Hazard Class: 3. ID #: UN1133. Packaging Group: II. Label: Flammable Liquid.

For Less than One Gallon: DOT Shipping Name: Consumer Commodity. DOT Shipping Class: ORM-D.

Shipping Information for Individual Container Larger than One Liter: DOT Shipping Name: Adhesive. DOT Hazard Class: 3. ID #: UN1133. Packaging Group: II. Label: Flammable Liquid.

For Less than One Liter: DOT Shipping Name: Consumer Commodity. DOT Shipping Class: ORM-D.


We Also Recommend