Menu
Cart 0
SCIGRIP IPS Weld-On #45 Adhesive

Must Be Shipped Ground

SCIGRIP IPS Weld-On #45 Adhesive

  • $17.07


  • SCIGRIP®45 is formulated for bonding a wide variety of metals, plastics, wood, concrete, brick and many other substrates
  • SCIGRIP 45 is recommended for a variety of applications and industries including sign assembly and other fabrication and manufacturing uses where high bond strength and environmental resistance is required
  • This adhesive is especially suitable for bonding aluminum, CRS, brass, copper, galvanized steel and other metals
  • Excellent adhesion is also obtained on plastics such as PVC, polycarbonate, ABS, acrylic and PETG
Description

SCIGRIP 45 is a fast curing, two-component, low VOC, reactive structural adhesive. When mixed and applied, it polymerizes at room temperature to form high strength bonds within an hour. The adhesive has excellent corrosion resistance, good gap-filling capabilities, weatherabiltiy and outstanding impact strength at low and high temperatures. Once cured, the adhesive will withstand a temperature range of -20°F (-29°C) to 200°F (93°C). Theelongation will remain the same even at high temperatures up to 200°F (93°C). UL 746C (aluminum, fiberglass).

Technical
Download - Technical Data Sheet

TYPICAL BOND STRENGTH

Substrate Material Aged Bond Strength, lbs/in2 (kg/cm2)
2 Hours* 24 Hours* 72 Hours*
Aluminum 2000 (140.62) 2200 (154.68) 2300 (161.71)
Cold Roll Steel 1900 (133.59) 2250 (158.20) 2300 (161.71)
Brass 1600 (112.50) 1700 (119.53) 2000 (140.62)
Copper 1100 (77.34) 1200 (84.37) 1500 (105.47)
Galvanized Steel 1700 (119.53) 2100 (147.65) 2300 (161.71)
ABS 1400 (98.43) 1500 (105.47) 1600 (112.50)
Polycarbonate 1600 (112.50) 1700 (119.53) 1800 (126.56)
PVC 1600 (112.50) 1700 (119.53) 1700 (119.53)
Acrylic 1700 (119.53) 1900 (133.59) 2000 (140.62)
PETG 1600 (112.50) 1650 (116.01) 1700 (119.53)

Substrate thickness: 0.25 inch (0.64 cm). Bond area: 1.0 in2 (6.45 cm2). Bond strength data was obtained using the compressive shear strength method (ASTM D-2564).

ADHESIVE PROPERTIES AND CHARACTERISTICS @ 73°F (23°C)

Color Tan Fixture Time 15 Minutes
Viscosity 500,000 ± 100,000 cps Time to reach 80% of ultimate bond strength 2 Hours
Reactivity 8 Minutes Specific Gravity Component A: 1.064 ± 0.02
Component B: 1.295 ± 0.02
Tack Free Time 1 hour, 0.02 inch (0.05 cm) film thickness Working Time 5 – 6 Minutes
Shelf Life 1 year
Directions

DIRECTIONS FOR USE

SCIGRIP 45 is packaged in a twin-syringe cartridge that dispenses product in a 4:1 mix ratio. The cartridge must be inserted in the dispensing gun and the mixing tip attached prior to dispensing.

  • Before inserting the cartridge in the dispensing gun, open cartridge valve and clean obstructions from cartridge nose and valve opening with a clean probe. Close valve.
  • Insert cartridge into dispensing gun. Open valve. Dispense a small amount of adhesive making sure that both components freely flow from the cartridge.
  • Attach the mixing tip to the cartridge. Press the dispensing gun to dispense and discard approximately 1 – 2 inches (2.5 – 5.0 cm) of the product, ensuring that the product is mixed properly in the mixing tip before use. If the mixing tip is left on the cartridge for a sufficient length of time without additional use, the adhesive may cure in the tip. If this happens, keep the mixing tip on the cartridge. When you are ready to dispense more adhesive, replace the mixing tip on the cartridge with a new one. Be sure to discard 1 – 2 inches (2.5 – 5.0 cm) of the product before use.
    Safety

    SAFETY AND ENVIRONMENTAL PRECAUTIONS

    This product is a flammable, reactive adhesive. It is considered a hazardous material. In conformance with the Federal Hazardous Substance Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state, and federal labeling, safety and other regulations. VOC emissions do not exceed 250 grams per liter.

    DANGER! FLAMMABLE. VAPOR HARMFUL. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE SKIN OR EYES.

    Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store away from direct sunlight between 50° – 80°F (10° – 27°C). Use only in adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values. See Section II of Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency and other conditions where short-term exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, goggles and impervious apron should be used. Carefully read Material Safety Data Sheet and follow all precautions. Component A contains Methyl Methacrylate Monomer (80-62-6). Component B contains Catalyst-Initiator and Benzoyl Peroxide (94-36-0). Do not use this product for other than intended uses. “Title III Section 313 Supplier Notification:” This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all Material Safety Data Sheets that are copied and distributed for this material.

    FIRST AID

    Inhalation: If overcome with vapors, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.

    Eye Contact: Flush with plenty of water for 15 minutes and call a physician.

    Skin Contact: Wash skin with plenty of soap and water for at least 15 minutes. If irritation develops, get medical attention.

    Ingestion: If swallowed, give 1 or 2 glasses of water or milk. Do not induce vomiting. Contact physician or poison control center immediately.

    SHIPPING

    Shipping Information for One Liter Kit and Above: Proper Shipping Name: Adhesive. Hazard Class: 3. Identification Number: UN 1133. Packing Group: II. Label Required: Flammable Liquid.

    For Less than One Liter: Proper Shipping Name: Consumer Commodity. Hazard Class: ORM-D


    We Also Recommend